GBPI ST50 Spectrophotometer

Application Use for test the light transmittance and haze degree of all transparent and semi-transparent parallel plane samples (plastic plate, sheets etc), and turbidity or clarity of liquid samples (water, drinks etc), used in the industries of plastics, membrane, coatings and paints, printing ink, research institute and so on.

P60 Standard Light Source Used for color observation, color contrast and color matching in a wide range of industries of printing, paints, printing ink, plastics, dyeing and so on.

1.Perfect combination of the beautiful appearance and the ergonomic structure design; 2.Combined LED light sources with long life and low power consumption, including UV light; 3.Switchable apertures: Φ2/4/8mm, adapt to more samples; 4. Accurately measure reflectance spectrum, CMYK density and Lab value of the sample; 5.High-configuration electronic hardware: 3.5-inch TFT true-color screen, capacitive touch screen, concave grating, 256-pixel dual-array CMOS image sensor, etc.； 6.Two standard observer angles: 2/10, multiple light source modes and color systems; 7.USB mode is widely used. 8.Large-capacity storage space, over 10,000 test data; 9.Especially suitable for process control and quality control of printing plants;10. PC software has powerful function expansion.

  Introduction GBPI haze meter can easily achieve ASTM D1003 non-compensation method, ISO 13468 compensation method, full light transmittance,haze test.Open sample bin can be vertically and horizontally tested to accommodate more samples to be tested.The YH1200 haze meter uses a PD array detector to meet the CIE V(λ)2 degree visual response. The compensation method can be used to measure the light transmittance and haze with high precision and repeatability.   Technical Advantage 1.Double standard ISO&ASTM Able to meet the test standard requirements of different users, in accordance with ASTM D1003/1044,ISO 13468,ISO 14782,GB/T 2410,JJF 1303-2011,CIE 15.2,JIS K7105,JIS K7361,JIS K 7136   2.Easy to operate, faster and more accurate measurement The YH1200 haze meter is equipped with a large-size touch screen for easy operation.With a PD array detector, CIE V(λ)2 degree visual response enables high precision and repeatable transmittance and fog measurements.USB data output device for docking with laboratory system.   3.Dynamic measurement Independent light source detector and temperature sensor, constantly monitor light source and environmental change, ensure the reliability of test data.   4.With compensation port, so that the measurement data more accurate Meet ASTM D1003 non-compensation method, ISO 13468 compensation method, full light transmittance, fog test, provide more accurate test results.   5.Easy to measure and widely applicable to samples Open measuring area, vertical and horizontal testing, suitable for more samples to be tested.   6.Quality control software It provides powerful software for measuring and analyzing fog and light transmittance, which is suitable for quality monitoring and tabulated management of fog and light transmittance data in various industries.The management of users will be digitized at the PC end, the difference of fog and light transmittance will be compared, and the test report form will be generated to facilitate customer customization and management.   Application YH1200 haze meter is widely used in glass processing, plastic processing, film processing, screen processing, packaging industry, liquid pharmaceutical analysis and other aspects.   Specification Product Model GBPI Haze Meter Optical Geometry Transmittance：0/D (Parallel light illumination, diffuse viewing); Conform to the standards: ASTM D1003/1044,ISO 13468,ISO 14782,GB/T 2410,JJF 1303-2011,CIE 15.2,JIS K7105，JIS K7361,JIS K 7136 Characteristic The instrument can easily achieve ASTM D1003 non-compensation method, full light transmittance,haze test. Open measuring area for vertical and horizontal testing. In glass processing, plastic processing, film, screen processing, packaging and other industries are widely used in transmittance,haze detection. Integrating Sphere Size Φ154mm Light Source 400nm to 700nm, combined LED light Spectrophotometric Mode / Sensor The PD array detector satisfies CIE V(λ)2 degree visual response Wavelength Range / Wavelength Interval / Semiband Width / Measurement range 0~100% Measuring Aperture Φ20mm/Φ15mm/Φ8mm/Φ4mm(Select a single aperture) Sample Size Thickness ＜170mm Color Space / Color Difference Formula / Other Colorimetric Index Haze(ASTM D1003/1044,ISO13468),Transmittance T(ISO),Transmittance T(ASTM) Observer Angle 2° Illuminant D65,A,C Displayed Data PASS/FAIL Result Measuring Time About1.5s Resolution 0.01unit Repeatability Φ20mm,within 0.05 (After preheating and calibration of the instrument, standard deviation values of standard haze tablets with a test haze of about 30 for 30 times were taken at intervals of 5s.) Inter-instrument Error Φ20mm,with 0.4 (After the instrument is preheated and calibrated, the standard deviation between the standard haze tablet and the reference value is tested at an interval of 5s.) Dimension L*W*H=290X211X511mm Weight About7.6kg Power AC 24V, 3A Power adapter power supply Illuminant Life Span 5 years, more than 3 million times measurements Display 7-inch TFT color LCD, Capacitive Touch Screen Data Port USB, Print serial port Data Storage Standard 1000 pcs,sample 20000 pcs Language Simplified Chinese,Traditional Chinese,English Operating Environment 0~40℃（32~104°F） Storage Environment -20~50℃（-4~122°F） Standard Accessory Power Adapter, User Guide,Quality Management Software (download from the official website),USB cable,0% calibration box, measuring aperture. Optional Accessory Micro-printer,Test fixture, standard haze sheet, foot switch Note: The specifications are subject to change without notice.      

  Application used to detect the gloss of plastic film, paper, ink, adhesive, etc. Multi-point measurement and data processing can be performed on the sample, and parameters such as average value, standard deviation and coefficient of variation can be printed directly. The machine has high precision and good stability, and can measure the glossiness of flat products such as paint, paper, plastic, ceramic, stone and metal.   Feature  Full-function intelligent design, light touch key operation.  Automatic measurement and manual measurement function.  For single point or no more than 10 points measurement, calculate the average value, root mean square, coefficient of variation and print out the result.   Standards  Angle International Standard Chines Standard Application 20 ISO-2813 ISO8254 GB9754 GB8807 Coating Plastic 20 TAPPI-T653 ASTM-D1834 GB8941.1 Paper 45 ISO-2767 GB8941.2 Metal compound paper 45 ASTM-C346 ASTM-D2457 GB8807 Ceramics、Plastic 45 JIS-E8741   Coating 60 ISO-2813 ASTM-D2457 GB9754 GB9966 GB8807 Coating Stone Plastic 75 TAPPI-T480 GB9841.3 Paper 85 ISO-2813 GB9754 Coating   Specifications Item Specification Test range 0-199.9 Gloss units Precision ±1.0 Gloss units Stability Not more than 0.5 gloss unit / every 30 minutes Repeatability Not more than 0.5 gloss unit Measuring probe size 180mm×100mm×50mm Power 25w/ 220vAC，50HZ      

Oxygen transmission rate (OTR) is the measurement of the amount of oxygen gas that passes through a substance over a given period. It is mostly carried out on non-porous materials, where the mode of transport is diffusion, but there are a growing number of applications where the transmission rate also depends on flow through apertures of some description.

Introduction N530 2.0 is based on the test principle of differential pressure method, It's designed with reference to GB/T 1038, ISO 2556 and other standards. Adopt high-precision pressure sensor and automatic pressure difference keeping technology, high test accuracy. It is suitable for the gas permeability test of films, sheets, papers, packages and related materials in the fields of food, medicine, medical equipment, daily chemicals, photovoltaic electronics, etc. It provides a wide range and high-efficiency gas transmission rate test of high, medium and low gas barrier materials.

Introduction This product is designed and manufactured based on the coulometric sensor method and conforms to GB/T 19789、ASTM D3985.This instrument can be used to measure the oxygen transmission rate of barrier materials with high and medium barrier properties with high accuracy and high efficiency.Y310Lis applicable to the determination of oxygen permeability of plastic films, sheeting, paper, and other packaging materials used in food, pharmaceutical, medical apparatus, consumer products, photovoltaic and electronic industries, etc.

  AUTO ZF1800G Total Migration & Non-Volatile Residue Tester Full-automatic Evaporation Residue & Loss on Drying Analyzer for Pharmaceutical, Food Contact, Chemical & Water Quality Testing Need technical datasheet, quotation or application support? Get free consultation from GBPI's testing instrument experts. Click for Free Consultation Introduction The AUTO ZF1800G Total Migration & Non-Volatile Residue Tester adopts an integrated system design of water bath evaporation, heating drying, cooling and constant-weight weighing. The whole test process runs fully automatically without manual operation. It is suitable for total migration (non-volatile residue, evaporation residue) tests in purified water, pharmaceutical packaging materials, food contact materials, cigarette tipping paper, chemical reagents and other fields. It can also be used for moisture content and loss on drying of solid samples, as well as total dissolved solids testing in water quality inspection. Test Principle Transfer the test solution into the solvent dish of the automatic feeding system. The empty dish is heated, cooled and weighed according to the set temperature. Repeat the steps until the constant weight is reached. The solution is evaporated to dryness in a water bath below the boiling point of the immersion liquid. The chamber is heated to 105℃ for drying and then cooled. After the evaporating dish is cooled, the balance judges the constant weight, and the experiment ends once the constant weight requirement of the test item is satisfied. Compliance Standards Purified Water: Purified Water in Chinese Pharmacopoeia Volume II, EP9.0 WATER, PURIFIED Pharmaceutical Packaging: Non-volatile residue item in extractables test of National Pharmaceutical Packaging Material Standard Food Contact Materials: GB 31604.8-2016, EN 1186-3:2002 method A, Standards and Specifications for Utensils, Containers and Packages of Korea Ministry of Health and Welfare chapter IV 2-8 Cigarette Tipping Paper: YQ/T 59-2015 Baijiu: GB/T 10345-2022 Method of Analysis for Baijiu Chemical Reagents: GB/T 9740-2008, ISO 759 Water Quality: GB 8538-2016, DZT0064.9-2021, GB/T 14415-2007, GB/T 5750.4-2006 Solid Samples: Extractables and Loss on Drying in Chinese Pharmacopoeia Volume IV, USP40-NF35<921> WATER DETERMINATION Specifications Item Technical Parameters Measuring Range 0 g ~ 80 g Balance Resolution 0.1 mg Balance Weighing Range 0 g ~ 220 g Constant Weight Tolerance 0.3 mg, adjustable Water Bath Temperature Range Ambient ~ 100℃ Oven Temperature Range Ambient ~ 125℃ Temperature Control Accuracy ±0.5℃ Number of Sample Positions 18 Evaporating Dish Volume 200 mL Gas Port Size Φ8 mm Overall Dimension 1200 mm(L) × 850 mm(W) × 1335 mm(H) Power Supply 220V,50Hz Rated Power 7000 W Operation System Windows 10 Pro 64-bit Features Dual-temperature Integrated Control System, Upgraded Automation Integrated workflow of water bath evaporation, drying, cooling and constant weight for automatic, efficient and precise testing. Adopts automatic feeding mechanism controlled by pneumatic valve with residual volume less than 0.1 mL, no waiting or manual attendance required. Built-in water bath with liquid level sensor for automatic water level detection, water filling, draining and temperature control. High-precision Imported Balances with Isolation Protection Equipped with 2 high-precision imported balances, constant weight of 0.3 mg can be achieved after two drying cycles. Balances are installed in a stable shield with water-circulation interlayer to keep stable temperature and humidity during weighing. High Throughput & Wide Compatibility 18 independent test stations with separate data output to meet high-throughput testing needs. Compatible with purified water, n-hexane, ethanol, acetic acid, chloroform and other organic solvents. Cooling & Recovery System for Efficient Solvent Recycling Built-in circulating water cooling pump maintains low chamber temperature. Eco-friendly, cooling down to room temperature within 30 min. Equipped with solvent recovery bottle, solvent recovery rate over 90%. Intelligent Operating System, Global Compliance Real-time display of weighing data, temperature and humidity curves; data is automatically saved for query. Designed in accordance with GMP annex for computerized systems, flexible parameter setting for different standards. Audit trail function for full data traceability, user permission management available. Supports multiple data output formats, electronic signature and online report approval. Laboratory Intelligent IoT Platform The instrument can connect to the IoT platform for network digital management. Authorized users can remotely log into the IoT platform, access the instrument software interface, manage test data and perform remote fault diagnosis. Application Image Application Field Description Purified Water Suitable for testing the non-volatile content of purified water and sterile water for injection in the pharmaceutical industry. Pharmaceutical Packaging Materials Suitable for the test of non-volatile matter items in the dissolution test of plastic and rubber pharmaceutical packaging materials. Food Packaging Materials Suitable for various food utensils, containers and food packaging films, cans or other various food tools, pipes and other products made of polyethylene, polystyrene, polypropylene, perchlorinated vinyl resin as raw materials in different food simulants. Determination of total migration after immersion. Cigarette Pack Materials Suitable for total migration test of cigarette tipping paper soaking solution. Chemical Reagent Suitable for the evaporation residue test of chemical reagents, such as ethanol, acetic acid, n-hexane, chloroform and other organic solvents whose boiling point is lower than 100℃. Domestic Water and Drinking Water, Industrial Water, Sewage Suitable for the total dissolved solids test of drinking water, drinking natural mineral water, groundwater, drinking water, swimming pool water, urban sewage, industrial boiler water, etc. Solid Samples, Pharmaceutical Particles Suitable for loss on drying, dry content or moisture testing of solid samples, such as hollow capsules, noncrystalline cellulose and other pharmaceuticals or other solid particles. Ready to upgrade your total migration and non-volatile residue testing workflow? Contact GBPI today for datasheet, quotation and professional testing solution. Click for Free Consultation

Vacuum Coating Thickness Tester is applied to various vacuum aluminum film, aluminized paper, and other conductive coating materials to test the resistance value, evenness, thickness and so on.

High Precision DSC Differential Scanning Calorimeter Product Introduction This DSC is our highest-precision differential scanning calorimeter. It is equipped with imported thermocouple sensors featuring ultra-high sensitivity. The signal acquisition circuit adopts full shielding protection design, delivering strong anti-interference capability and excellent baseline stability. Adopting touch screen operation, this instrument can perform glass transition temperature test, phase transition analysis, melting enthalpy measurement, product stability evaluation and oxidation induction period test, covering a wide range of testing applications. Test Principle By measuring the heat flow difference between the sample and the reference material under programmed temperature control, the instrument analyzes thermal characteristic parameters such as melting point, glass transition temperature and oxidation resistance of polymer, pharmaceutical and packaging materials. Technical Parameters Temperature Range Room Temperature ~ 550 ℃ (Air Cooling) Temperature Resolution 0.01℃ Temperature Fluctuation ±0.1℃ Temperature Repeatability ±0.1℃ Heating Rate 0.1～100℃/min Constant Temperature Duration Programmable ≤ 24h Temperature Control Modes Heating, Constant Temperature DSC Heat Flow Range 0～±600mW DSC Resolution 0.01μW DSC Accuracy 0.001mW Power Supply AC 220V, 50Hz (Customizable) Atmosphere Control Gas Nitrogen, Oxygen (Automatic Instrument Switching) Gas Flow Rate 0-300ml/min Gas Pressure 0.2MPa Display Screen 7-inch 24-bit Color LCD Touch Screen Data Interface Standard USB Port Calibration Standard Comes with Indium & Tin Reference Materials for User Self Temperature Calibration PC Software Compatibility 3-in-1 Host Software, Compatible with TGA & Synchronous Thermal Analyzers Thermocouple Configuration 3 Groups of Thermocouples: Sample Temp, Furnace Temp, Internal Ambient Temp Technical Features

  W401 2.0 water vapor transmission rate tester is designed and manufactured according to  ASTM F1249 and ISO standards, based on the testing principle of infrared method, it provides wide range and high efficiency water vapor transmission rate test for high, medium and low barrier materials is suitable for water vapor transmission performance testing of films, sheets, paper, packaging and other related materials in the fields of food, medicine, medical equipment, daily chemistry, photovoltaic electronics, etc. It is an ideal configuration instrument for off-line or on-line testing of the barrier properties of packaging materials for production units in the packaging industr