Inclined Surface Coefficient Of Friction Tester

The coefficient of friction tester is used to test the coefficient of frictionof plastic film, thin sheet, paper and so on, widely used in packaging industry, film-making companies and packaging material inspection agencies.

Coefficient of friction testers is used to test the coefficient of frictionof plastic film, thin sheet, paper and so on, widely used in packaging industry, film-making companies and packaging material inspection agencies.

  The coefficient of friction tester GM-4 is a measuring instrument developed and manufactured by the Guangzhou Biaoji R&D team based on various test standards of GB, ISO, ASTM and market demand. The measured friction coefficient determines the smoothness and opening difficulty of the film. and uniformity can be accurately determined, so as to correctly guide the production. It is suitable for measuring the static friction coefficient, dynamic friction coefficient and peel strength of plastic films, composite films, aluminum foils, aluminized films, plates, rubber, ceramics and other materials when sliding.        

  GBB-C Vertical Heat Sealing Tester Product Introduction GBB-C vertical heat sealing tester accurately measures heat sealing temperature, time, pressure and other performance parameters of plastic stand-up pouches, paper-plastic composite pouches and metal composite pouches. Optimal sealing conditions can be confirmed by testing sealing characteristics of different packaging materials. Testing Principle Place sample on the lower support plate and adjust height properly. Set sealing temperature, time and pressure as required, then start the device. The upper fixture seals samples automatically according to preset parameters. Step on foot switch to complete sealing in manual mode. In automatic mode, cyclic sealing runs repeatedly following set duration. Compliance Standards QB/T 2358-1998, ASTM F 2029, YBB00122003-2015 Technical Parameters Temperature Range Room temperature ~ 250℃ Temperature Accuracy ±1℃ Sealing Time 0.1s ~ 99.99h Sealing Pressure 0~1 MPa Sealing Surface 300×5.5mm smooth cutter, lower rod with silicone pad Operation Mode Manual & Automatic, external cylinder Air Source Compressed air Overall Dimension 730×400×540 mm Weight 33.8kg Power 1200 W Power Supply AC 220V, 50Hz Product Features Independent Temperature Control Temperature sensors installed at the rear of sealing cutters, inner and outer cutters support separate temperature setting. Dual Optional Test Modes Automatic mode realizes efficient repetitive sealing; manual mode equipped with foot switch for safe and easy operation. Advanced Pneumatic Driving System Composed of pressure gauge, regulating valve and cylinder, air pressure can be precisely adjusted for stable and efficient sealing work. Comprehensive Customization Service Anti-stick coating upgrade available. Customizable shape, size and surface smoothness meet diversified research demands. Application Fields Plastic Stand-up Pouch Paper-plastic Stand-up Pouch Aluminized Stand-up Pouch Boxed Milk

Product Introduction The headspace gas analyzer adopts the destructive puncture detection method and is equipped with high-precision oxygen sensors and carbon dioxide sensors to accurately detect the O2 and CO2 content of hollow packaging containers such as packaging bags, bottles, cans, etc. The analysis of the content of the headspace gas in the packaging can make a reasonable judgment on the product quality, the validity of the shelf life prediction, and the rationality of the packaging design. At the same time, it can also be used as a means of packaging tightness testing. It is a better choice for modified atmosphere preservation (MAP, CAP) packaging, large infusion bottles (bags), residual oxygen in the headspace of prefilled needles, residual oxygen detection in vials, and the results of residual oxygen detection for various food and medicines. Nowadays, the headspace gas analyzer has become an important method to check the quality of packaging design and one of the important methods to verify the product shelf life. Our headspace gas analyzer GB-DK can quickly detect O2 in production lines, warehouses, laboratories and other occasions. And CO2 content to guide production.   Test principle The gas in the sample is drawn into the sensor by a vacuum pump. The sensor outputs the current and voltage signals of the O2 and CO2 (optional) concentration in the gas in the sample in real time. The instrument calculates the content of O2 and CO2 in the gas by obtaining the current and voltage signals output by the sensor. After reaching the end conditions of the experiment, the test stops, and the instrument records the concentration of O2 and CO2 in the measured gas in the sample.   Technical parameter Item Parameter Gas to be Measured O2 (standard configuration) CO2 (optional) Measurement Principle Fluorescence optics infrared absorption Measurement Range 0%～25% (for O2) 0%~100% (for CO2) Measurement Accuracy ±0.2% ±2% Sample Size ≥5 mL (at standard atmospheric pressure) (for O2) ≥20 mL (at standard atmospheric pressure) (for CO2) Dimensions 350 mm (L)×330 mm(W)×200 mm(H) Power Supply 220 VAC±10 % 50Hz/120 VAC±10 % 60 Hz Net Weight 5kg    Features 1.Using high-precision sensors, high accuracy, good stability, long-term operation, long service life. Over-range automatic protection function to avoid damage to important sensors when the instrument fails. 2.The needle/probe safety holster is used to ensure safe testing and fast sampling. 3.Oxygen and carbon dioxide can be detected at the same time, and carbon dioxide gas can be selected for analysis according to different user needs. The sampling volume is at least 3 ml. 4.Built-in operating system, the system is equipped with an ARM control system to control the host through a touch screen (testing equipment and control software are combined into one); at the same time, the system can be expanded, such as connecting to the laboratory LIMS system. 5.The software is designed according to the requirements of the computerized system in the new version of the GMP appendix, and users are divided into multiple levels such as operators and administrators (such as administrators, operators, observers, etc. but not limited to these levels). 6.It has the audit trail function, which can realize the audit trail of the system, project operation, and method to ensure the safety and integrity of the test data. 7.Personalize the test report, set the report module that needs to be displayed, and output the report in PDF mode. The micro printer can print test reports in real time.  

The Leakage tester GB-M2 is designed and manufactured in accordance with the relevant provisions of GB/T15171 Test method for leaks in sealed flexible packages. It is used to detect the sealing condition of plastic packaging bags and containers, and it is applied to used in industries of food, beverage, pharmaceuticals, personal care and so on. Through test can effectively compare and evaluate the sealing technology and sealing performance of packaging parts, and provide scientific basis for determining the relevant technical indicators. It can also be used to test the sealing performance of the specimens after dropping and compressing test.

Test Principle Firstly submerge the specimen in the water in the vacuum chamber, and then evacuate the vacuum chamber to form differential pressure between the inside and outside of specimen. The seal property can be obtained by observing the steady progression of bubbles from the specimen or observing how the specimen expands and restores to its original shape after vacuum release.

  Infrared method water vapor transmission rate tester W405L is a high-end precision packaging material testing instrument, newly developed and upgraded by GBPI Research and Development Team based on ASTM, GB standard requirements and market demand. It is used to test the water vapor transmission rate of samples under set temperature and humidity conditions. It is suitable for the water vapor transmission rate performance test of films, sheets, papers, packages and various materials in the fields of food, medicine, medical equipment, daily chemistry, photovoltaic electronics, etc.      

Product Introduction This professional machine is designed for automatic tube insertion and heat-sealing of straws and bags. It is suitable for straws of various diameters, lengths, and models, making it the preferred automated equipment for packaging bags such as laundry detergent spout side bags, beverage/juice spout bags, oil/grease spout bags, and inclined-mouth outdoor foldable water bags. It can be customized to connect with filling production lines.

The tear tester (elemendorf method) tests the tear resistance of paper, film, PVC, polyolefin, polyester, composite film, sheet, non-woven fabric, textile, paper, and board, etc. It is controlled by computer automatically and can be tested independently.

Product Introduction The LC-3S manual precision sample cutter can be used for precision sample cutting in tensile testing of materials such as copper-aluminum foil, battery separators in the new energy industry, various plastic films, paper, paper-plastic composites, and metals. This product is easy to operate, safe, reliable, and durable. The cut samples are smooth without burrs, enabling precise cutting of samples and effectively avoiding measurement errors caused by poor sample cutting.   Product Features Item Technical Parameters Material Thickness ≤1mm Cutting Specification 15mm × 220mm (customizable) Equipment Size 250mm × 550mm × 400mm Weight 9kg   Product Features ✦ The sample cutter has a compact design, is sturdy and durable, easy to operate, and efficient.✦ The cutting blade is made of high-speed tool steel, with a high-hardness edge that is sharp and durable. The cut samples are undamaged with smooth edges without burrs.✦ The width of the cut sample is 15mm, with high cutting precision, fully meeting standard requirements. It also supports customization of different sample cutting widths.✦ Both sides of the blade are designed with safety protection barriers, ensuring safe and reliable sample cutting process.

This machine is used to test the compression, deformation resistance and stacking of corrugated carton, honeycomb board box and so on.