This product is based on the testing principle of coulometric oxygen sensor, designed and manufactured with reference to ASTM D3985 and other standards. It adopts high-precision imported oxygen sensor with high testing accuracy. It is suitable for oxygen transmission performance testing of films, sheets, papers, packaging and related materials in the fields of food, pharmaceuticals, medical devices, daily chemicals, photovoltaic electronics, etc. It provides wide range and high efficiency oxygen transmission rate testing for high, medium and low oxygen barrier materials.

This product is based on the testing principle of the coulometric sensor method testing Oxygen, and is designed and manufactured with reference to ASTM D3985 and other standards. Adopting high-precision imported oxygen sensor, high test accuracy,it is suitable for oxygen transmission performance testing of films, sheets, paper, packaging and related materials in the fields of food, medicine, medical equipment, daily chemicals, photovoltaic electronics, etc., and provides a wide range and high-efficiency oxygen transmission rate detection for high, medium and low oxygen barrier materials.

Introduction This product is designed and manufactured based on the coulometric sensor method and conforms to GB/T 19789、ASTM D3985.This instrument can be used to measure the oxygen transmission rate of barrier materials with high and medium barrier properties with high accuracy and high efficiency.Y310Lis applicable to the determination of oxygen permeability of plastic films, sheeting, paper, and other packaging materials used in food, pharmaceutical, medical apparatus, consumer products, photovoltaic and electronic industries, etc.

1.Function It’s widely used in rubber products, magnetic materials, circuit boards, muti-layer circuit boards, IC, LCD, electronics and other products sealing performance testing.   2.Characteristics 1) The imported double-temperature structure with high temperature resistant solenoid valve is used to minimize the failure rate. 2) Independent steam generation chamber to avoid direct impact of steam on the product, so as not to cause partial damage to the product. 3) The door lock labor-saving structure solves the shortcomings of the locking difficulty of the first-generation product disc handle. 4) Cool air before the test; the design of the exhaust air in the test (air discharge in the test barrel) improves the pressure stability and reproduction. 5) Ultra long-term experimental running time up to 400 hours. 6) Water level protection, through the test room water level Sensor to detect protection. 7) Tank with anti-pressure design, the box body with pressure (150 ° C) up to 2.65kg, in line with the water pressure test of 6kg. 8) Two-stage pressure safety protection device, adopting two-stage combined controller and mechanical pressure protection device. 9) Safety protection pressure button, two-stage automatic pressure button for emergency safety device. 10) Bias test terminal withstand voltage up to 3000V (optional) 11) USB for exporting the history data, curve. 3.Technical parameters 1)Temperature range: +100°C～+132°C (Saturated vapor temperature) 2)Humidity Range: 100% steam Humidity 3)Humidity Control Stability: ±1%RH 4)Working pressure: 1.2~2.89kg/cm2 (including 1atm) 5)Time Range: 0 Hr to 999 Hr 6)Pressurization time: 0.00 Kg ~ 1.04 Kg/cm2 about 45 minutes 4.Material of chamber 1)Test chamber size:∮300 mm x L500 mm; 2)Overall size: W900x D900 x H1400 mm; 3)Inner barrel material: Stainless steel plate material (SUS# 316, 3mm); 4)Outer barrel material: stainless steel plate material or spray plastic; 5)Insulation material: rock wool and hard polyurethane foam insulation 6)Steam chamber heating tube: Titanium tube is heated and never rusts. 7)Control System: Taiwan-made Delta color touch PLC to control humidity and steam temperature (using PT-100 Platinum temperature sensor). (Imported large-screen touch controller) 5.Mechanical structure 1)Round inner box, stainless steel round test inner box structure, in line with industrial safety container standards, can prevent dew condensation design during test. 2)Round lining, stainless steel circular lining design, can avoid direct impact of vapor latent heat on the sample. 3)Precision design, good air tightness, low water consumption, and can be operated continuously for 400Hrs every time. 4)The patented packing design makes the door and the box more tightly combined, which is completely different from the traditional extrusion type, and can extend the packing life. 5)Critical point LIMIT mode automatic safety protection, abnormal cause and fault indicator display. 6)Security Protection: a)Imported high temperature sealed solenoid valve adopts double circuit structure to ensure no leakage of pressure. b)The whole machine is equipped with over-pressure protection, over-temperature protection, one-button pressure relief, manual pressure relief and multiple safety guarantee devices to ensure users to the greatest extent. c)Use and safety. d)Back pressure door lock device, the test box door cannot be opened when there is pressure inside the test chamber. 6.Other accessories. 1)Test rack 1 group 2)Sample tray   7.Ambient environment & Facilities. 1)It can be allowed to use the working environment temperature 5 ° C ~ 30 ° C; experimental water: pure water or distilled water 2)System power fluctuations should not be greater than ± 10, 220V 20A.    

Product Introduction This professional machine is designed for automatic tube insertion and heat-sealing of straws and bags. It is suitable for straws of various diameters, lengths, and models, making it the preferred automated equipment for packaging bags such as laundry detergent spout side bags, beverage/juice spout bags, oil/grease spout bags, and inclined-mouth outdoor foldable water bags. It can be customized to connect with filling production lines.

Torque tester HP-200 is a testing instrument for bottle cap locking and opening based on ASTM and GB standard requirements and market demand developed and manufactured by GBPI R&D team. For bottle packaging products, nozzle packaging products and tube packaging products, the size of the cap opening torque is one of the key control parameters, which has a great impact on the intermediate transportation and final consumption of the product.It is suitable for measuring the size of the locking and opening torque of bottle products, and is an indispensable test equipment in the production process.

  Introduction Designed and manufactured according tostandards likeGB/T 8809、ASTM D3420, GBG-L2 Pendulum Impact Tester is suitable for determining pendulum impact resistance of the film materials,composite film,metallic foil and so on. The machine can be used in scientific research, teaching, industrial and mining enterprises, laboratory, research institute and quality supervision department.  

  The coefficient of friction tester GM-4 is a measuring instrument developed and manufactured by the Guangzhou Biaoji R&D team based on various test standards of GB, ISO, ASTM and market demand. The measured friction coefficient determines the smoothness and opening difficulty of the film. and uniformity can be accurately determined, so as to correctly guide the production. It is suitable for measuring the static friction coefficient, dynamic friction coefficient and peel strength of plastic films, composite films, aluminum foils, aluminized films, plates, rubber, ceramics and other materials when sliding.        

  Product Introduction     The GB-ML Leakage Tester is a professional testing instrument powered by compressed air, which controls the lifting and lowering of the sealing barrel lid through an air cylinder.   Adopting a high-precision electronic pressure sensor and a microcomputer control system, it effectively compares and evaluates the sealing process and sealing performance of flexible packages, and provides a scientific basis for determining relevant technical requirements.   This equipment is suitable for sealing performance testing of flexible packages in food, pharmaceutical, daily chemical and other industries.   Testing Principle   The sample is immersed in water, and a vacuum is applied to the vacuum chamber to create a pressure difference between the inside and outside of the sample.   The sealing performance is judged by observing gas escaping from the sample or water penetrating into the sample.     Applicable Standards   GB/T 15171, ASTM D3078-2002 (2013), USP 1207.2 Item Technical Parameters Vacuum Degree 0～-90 kPa Vacuum Accuracy ±1% of indicated value Vacuum Holding Time 0.01 s～99.99 h Sealing Barrel Size Standard: Φ600×591 mm; other sizes optional or customizable Effective Vacuum Chamber Size Standard: Φ550×396 mm; other sizes customizable Air Inlet Pressure 0.6～0.8 MPa Power 50 W Instrument Dimensions 1005×802×1307 mm Power Supply 220 V, 50 Hz   Product Features   High-quality components, stable and reliable   Built-in high-precision pressure sensor with high sensitivity, enabling real-time monitoring of inlet pressure.   Full-automatic operation system   Vacuum degree and holding time can be set as required. The instrument automatically completes vacuuming, holding, stopping and air-releasing.   Brand-new pneumatic system with fast inflation and return, achieving balanced pressure inside and outside.   Key-controlled cylinder for automatic opening and closing of the sealing barrel lid, labor-saving and convenient.   Supports multiple test methods   Supports bubble method and dye penetration method for leakage / integrity testing.     Application Areas   Plastic Packaging   Leakage testing for plastic bags, plastic containers (bottles, cans, boxes), etc.   Glass Packaging   Leakage testing for food bottles, pharmaceutical glass containers, daily chemical glass bottles, etc.   Metal Packaging   Leakage testing for cans, easy-open cans, aerosol cans, metal hoses, etc.   Other Applications

Product Brief The N600E Battery Separator Air Permeability Tester is designed and developed in accordance with standards such as GB/T 36363-2018. Adopting the differential pressure method as its testing principle, it is professionally used for testing the air permeability of battery separators, breathable films, and related polymer materials. Testing Principle In an environment with controlled temperature, humidity, and normal pressure, the tester measures the time required for 100 mL of air to pass through a 6.45 cm² separator under an applied pressure of 1.21 kPa. Executed Standards GB/T 36363-2018, ISO 5636-5:2003, TAPPI T460 Technical Parameters Item Technical Parameters Test Range 60~12000 sec/100mL Resolution 0.1 sec/100mL Pressure Range 0~5 kPa Pressure Resolution 0.001 kPa Test Area 6.45 cm² Sample Size ＞50 mm×50 mm Instrument Dimensions 450 mm×400 mm×300 mm Power 100 W Power Supply 110~250 VAC, 50~60 Hz Product Features • The instrument's differential pressure is adjustable within the range of 0~5 kPa, with a precision of 0.001 kPa, fully meeting the test pressure requirements of different methods;• Supports multi-unit display (s/100mL and μm/(Pa·s));• The test range can be customized according to different sample requirements;• Excellent airtightness;• Arbitrary pressure adjustment, fully automatic operation, and automatic measurement and calculation of results;• Equipped with a color touch screen, no external computer required, enabling real-time observation of sample air permeability;• Built-in micro-printer for real-time printing of test reports;• The upper computer software is designed in accordance with the new GMP Appendix "Computerized Systems", supporting functions such as hierarchical permission management, audit trail, and electronic signature (optional).

To test the tensile strength, peeling strength, heat sealing strength, tearing strength, piercing strength of plastic film, composite film, tape, soft packaging material, rubber sheets, paper, non-woven fabrics and other packaging materials

  GBL-H2 Electronic Universal Testing Machine High Precision Mechanical Performance Tester Product Introduction GBL-H2 is a universal single-column electronic tensile testing machine developed by GBPI based on GB, ASTM standards and market demands. Equipped with high-precision sensors, it features high accuracy, stable loading and long service life. With LCD display and professional software, it shows real-time test curves and reports. Fully automatic operation with complete safety protections: limit protection, overload protection and emergency stop. Widely used for tensile, peeling, heat sealing, tearing, puncture tests of metal & non-metal materials in food, pharmaceutical, packaging industries, inspection centers and research institutes. Test Principle The prepared sample is fixed between two clamps. Start the instrument to make the clamps move relatively. The force sensor collects force changes, and the displacement sensor collects displacement changes, so as to calculate the tensile, peeling, heat-sealing, tearing and other performance indicators of the sample. Compliance Standards GB 8808 GB 13022 GB/T 1040 ASTM D882 ASTM E4 YBB Series QB/T Series Technical Parameters Item Parameter Force Range 0~300N (Optional 0~500N) Accuracy ±0.5% FS Test Speed 0~500 mm/min Displacement Accuracy ±0.5% Test Width 30mm (50/60mm customizable) Stroke 750mm (1000/1200mm customizable) Dimensions 600×500×1300mm Weight 65kg Power AC 220V 50Hz Product Features Ergonomic Design Desktop column structure, compact and easy to operate. High-Efficiency Test Tensile, peel, tear, puncture test available. High sampling rate 100 times/sec. Safety & Stability Triple safety protection, emergency stop, imported core parts. Intelligent System User management, audit trail, GMP compliant, off-line & PC control. IoT Platform (Optional) Data management, remote diagnosis and fault solving. Applications Plastic Films Film, composite, packaging materials, tape Composite Film Bags Composite bags, cooking bags, aluminum-plastic bags Paper Kraft paper, tissue, paper products Medical Patches Medical patches, plaster, cooling gel Adhesive Tape Insulation tape, medical tape, glass paper tape © 2025 GBPI | GBL-H2 Electronic Universal Testing Machine | Professional Testing Solution