packaging testing equipment Water Vapor Permeation Tester
Products
Home /

Environmental Test Equipment

/

Aging Test Chamber

/Salt spray test chamber GB-OSH-60

Salt spray test chamber GB-OSH-60

Inquiry now
Product Detail

 

1. FunFunction

Salt spray test chamber is used for the quality inspection and corrosion resistance test of a variety of materials, including metal plating, metal, electronic components, chemical coatings, paint, automobiles, motorcycles, metal ware, screws, springs, magnetic materials, organic and inorganic coating, anodizing, anti-rust oil industry etc. after the surface treatment.

 

1. ecGTechnical parameters

 

1. MODEL

GB-OSH-60

2. Temperature inside chamber

35℃±1℃/ 50℃±1℃

3. Temperature of pressure barrel

47℃±1℃/ 63℃±1℃ 

4. Inner size

W600 x H400 x D450mm  

5. External size

W1080 x H1080 x D650mm

6. Temperature Uniformity

≤±2℃

7. Uniformity Fluctuation

≤±0.5℃

8. Salt fog settlement

1~2ml/h.80cm2

9. Compressed air pressure

1.00±0.01kgf/cm²

10. Spray mode

Continuous or intermittent spray optional

11. Power supply

AC  220V   50Hz   1.5KW

a)  Temp. range: RT+10℃ ~ 55℃ (temperature up to 50C, thickening PVC or PP material is recommended )

b) Humid. range: ≥93%R.H

c) Controller time shown: 9.9s~9990hrs

d) Timer: 0~9999hrs.

e) Testing method: Neutral salt spray test (NSS test), acetic acid salt spray test (AASS test), salt spray test (SS test), copper accelerated acetic acid salt spray test method for salt spray test (CASS test) and so on; (For CASS test, we recommend the PP material chamber with high temperature resistance)

f) Specimen holder: It can meet the tilt test at 15 ℃ ~ 30 ℃ (two layers);

g) Air compressor: V-0.013/12.5(Customer provided); discharge pressure:1.25M; flow amount: 0.13m3/min

 

1. MMMaterial of machine body

a) Salt spray chamber adopts the quality PVC reinforced hard plastic plate, the surface is smooth and anti-aging, anti-corrosion;

b) Without any FRP material produced on the surface because of discoloration fibrosis. Plastic structure of the chamber is better to meet strong acid salt spray test under long-term without any damage.

c) Cover is imported transparent impact-resistant plate which is convenient to test specimen when test, that can cover and the box with a water seal to prevent leakage of salt spray.

 

2. AccAccording to CSN, JIS, ASTM standards, can be set to constant temperature control:

(a) Brine spray test: NSS (neutral);

· Temp. inside chamber: 35 ℃ ± 1 ℃

· Pressure air bucket: 47 ℃ ± 1 ℃

(b) Corrosion resistance test: CASS (copper acceleration), AASS (acid)

· Temp. inside chamber: 50 ° C ± 1 ° C

· Pressure air bucket: 63 ℃ ± 1 ℃

 

3. Watwatering system.

It adopts the auto watering system, supply water when lack of water.

4. HeaHeating system

Test temperature inside the cabinets is heated humidification water jacket, the heater adopts advanced titanium protective tube, built-in nickel-chromium alloy infrared heater core. Heating up fast, uniform temperature distribution; and saves about one half of the power compared to FRP tank jacketed heating.

5. ExeExecutive standard

GB/T 2423.17 Basic test procedures for electric and electronic products Ka"- salt spray test methods;

GB/T 10125 Corrosion tests in artificial atmospheres – salt spray tests;

ASTM B368 Test Method for Copper-Accelerated Acetic Acid-Salt Spray (Fog) Testing (CASS Test);

JIS Z2371-2000 Methods of salt spray testing etc.

ISO 9227 Corrosion tests in artificial atmospheres (Note: 2 collection device is required, bigger models than ZH-SH-90 (270L) is required; In some versions, it specifies over 400liters is necessary) 

ASTM B117-18 Standard Practice for Operating Salt Spray (Fog) Apparatus (Note: 2 collection device is required, bigger models than ZH-SH-90 is required )

 

Send A Message

Leave us a message, we will get back to you ASAP.

Related Products
Ozone Aging Test Chamber Ozone Aging Test Chamber (Dynamic Stretching) GB-OCY-150M
1 Function Ozone in the atmosphere is very little, while it’s a major factor in rubber cracking, the product simulate and enhance atmospheric ozone condition to study the role of ozone on the rubber, and to rapid identificate and evaluate rubber resistance for ozone aging and anti-ozone agent protection. According to“GB / T7762-2003 Test Method for Static Tensile Test of Ozone Resistance Cured Rubber or Thermoplastic Rubber”,“GB / T2951.21-2008 General Test Method for Insulation and Sheathing Material of Cable”,“GB / T 11206-2009 Rubber Aging test surface cracking method”, and other relevant standards of the test method. 2.1 Structure  All-in-one machine 2.2 Material a) Inner chamber: SUS304 stainless steel plate b) External chamber: SUS304 stainless steel plate or baking finish. Insulation: rigid polyurethane foam + aluminum insulation cotton with double protection. 2.3 Machine door a) Single door, open from left. b) Window frame / door frame with two silicone rubber seal and anti-condensation heating device. c)With observation window (W220xH250mm), lights above the window and door.  2.4 Requirements for sample holder (for dynamic-type only)       a)At both ends of the sample to be fixed with a clamp under the required elongation, the longitudinal direction of the specimen shall be substantially parallel to the direction of air flow when in contact with ozonized air. b) Clamps shall be made of a material (eg aluminum) which does not readily decompose ozone. c) Allow the sample to rotate at a speed between (20 ^ -25) mm / s, in a plane perpendicular to the dry gas flow, with each sample moving continuously along the same path. d) The time of one revolution of the same specimen is (8 ^ -12) min. The scanning area of the specimen shall be at least 40% of the effective area of the test chamber. Specimen preparation shall conform to the provisions of GB / T 9865.1. The test specimen is preferably cut from the new test piece and, if desired, may be cut from the finished product. At least 3 specimens shall be required for per test condition. The standard length of the specimen is not less than 10mm, and thickness not less than 0.2mm. The length of specimen between the two ends of the clamp before drawing is not less than 40mm. 3 Control panel a) Controller display b) Power switch c) Fault alarm d)Wavelength switch e)light switch button 4 Enclosure configuration a) With a stainless steel SUS # 304 shelf turntable b) One φ50mm lead hole:, and with a hole cover and silicone rubber plug. c) Move casters 4 pcs d) Horizontal mounting brackets 4 pcs e) There is a drainage hole in the back of the machine to facilitate the drainage of condensate; (8mm in diameter) Three-phase five-wire cable (four-core cable + protective grounding wire) 1 pc, (three meters long).
PCT test chamber PCT Test Chamber Pressure Cooker test chamber GB-OPCT-30
1.Function It’s widely used in rubber products, magnetic materials, circuit boards, muti-layer circuit boards, IC, LCD, electronics and other products sealing performance testing.   2.Characteristics 1) The imported double-temperature structure with high temperature resistant solenoid valve is used to minimize the failure rate. 2) Independent steam generation chamber to avoid direct impact of steam on the product, so as not to cause partial damage to the product. 3) The door lock labor-saving structure solves the shortcomings of the locking difficulty of the first-generation product disc handle. 4) Cool air before the test; the design of the exhaust air in the test (air discharge in the test barrel) improves the pressure stability and reproduction. 5) Ultra long-term experimental running time up to 400 hours. 6) Water level protection, through the test room water level Sensor to detect protection. 7) Tank with anti-pressure design, the box body with pressure (150 ° C) up to 2.65kg, in line with the water pressure test of 6kg. 8) Two-stage pressure safety protection device, adopting two-stage combined controller and mechanical pressure protection device. 9) Safety protection pressure button, two-stage automatic pressure button for emergency safety device. 10) Bias test terminal withstand voltage up to 3000V (optional) 11) USB for exporting the history data, curve. 3.Technical parameters 1)Temperature range: +100°C~+132°C (Saturated vapor temperature) 2)Humidity Range: 100% steam Humidity 3)Humidity Control Stability: ±1%RH 4)Working pressure: 1.2~2.89kg/cm2 (including 1atm) 5)Time Range: 0 Hr to 999 Hr 6)Pressurization time: 0.00 Kg ~ 1.04 Kg/cm2 about 45 minutes 4.Material of chamber 1)Test chamber size:∮300 mm x L500 mm; 2)Overall size: W900x D900 x H1400 mm; 3)Inner barrel material: Stainless steel plate material (SUS# 316, 3mm); 4)Outer barrel material: stainless steel plate material or spray plastic; 5)Insulation material: rock wool and hard polyurethane foam insulation 6)Steam chamber heating tube: Titanium tube is heated and never rusts. 7)Control System: Taiwan-made Delta color touch PLC to control humidity and steam temperature (using PT-100 Platinum temperature sensor). (Imported large-screen touch controller) 5.Mechanical structure 1)Round inner box, stainless steel round test inner box structure, in line with industrial safety container standards, can prevent dew condensation design during test. 2)Round lining, stainless steel circular lining design, can avoid direct impact of vapor latent heat on the sample. 3)Precision design, good air tightness, low water consumption, and can be operated continuously for 400Hrs every time. 4)The patented packing design makes the door and the box more tightly combined, which is completely different from the traditional extrusion type, and can extend the packing life. 5)Critical point LIMIT mode automatic safety protection, abnormal cause and fault indicator display. 6)Security Protection: a)Imported high temperature sealed solenoid valve adopts double circuit structure to ensure no leakage of pressure. b)The whole machine is equipped with over-pressure protection, over-temperature protection, one-button pressure relief, manual pressure relief and multiple safety guarantee devices to ensure users to the greatest extent. c)Use and safety. d)Back pressure door lock device, the test box door cannot be opened when there is pressure inside the test chamber. 6.Other accessories. 1)Test rack 1 group 2)Sample tray   7.Ambient environment & Facilities. 1)It can be allowed to use the working environment temperature 5 ° C ~ 30 ° C; experimental water: pure water or distilled water 2)System power fluctuations should not be greater than ± 10, 220V 20A.    
Xenon arc lamp aging test chamber Xenon arc lamp aging test chamber GB-OXD-15P
  1.Profile Xenon lamp aging test chamber simulates the full spectrum lamp with Xenon arc lamp to reappear the destructive wave. It serves for the environmental simulation and accelerated test for research and development, product development and quality control. Besides, the chamber also applies to the choice of new material, weathering test after composition of material and improvement for the current material. It simulate different environment, and show the material changes under the explosion of sunlight.   The chamber meets the standard: GB/T16585-1996 , GB14522-93 , GB/T16422.3-97, ASTM D2565 and so on. The Chamber is to determine the color fastness, aging resistance of textiles, plastics, coatings, rubber products or other materials by objecting to the simulated conditions of nature weather (sun, rain, temperature and humidity, etc.).     Technical parameters   2.Material of construction u Full spectrum lamp u Optional filter system u Water spraying function u Humidity control u Temp. control system in the chamber u Sample fixed hold of irregular shape u USA imported xenon arc lamp u Easy installation and operation, seldom daily maintainance. u Service life time deepens on the irradiance level, usually 1600hrs. It’s easy to replace the lamp, with filter of long service life time to ensure the necessary spectrum. 3.Technical parameters Model No., equipment name GB-OXD-15P Xenon aging test chamber Interior sizes   W500×D500×H600mm  Exterior sizes W1050×D1050×H1750mm (or so) Temperature range 0℃~80℃ Controller imported programmable 7inch touch screen Machine components material inner and outer 304# stainless steel Sample holder Aluminum alloy frame base Protection device residual-current circuit breaker (RCCB) to control the warning for loop overload, thermal protection and water shortage protection. Temp. deflection ±2℃  (without lighting) Humidity range 30%~98%R.H Humid. deflection ±2.5%R.H(Humid.≥75%R.H); ±3%R.H(Humid.≤75%R.H) without lighting Light source imported full spectrum xenon arc lamp(average useful life 1600hrs) Raining time 1~9999min (adjustable) Raining period 1~240min, interval(cut)adjustable lamp power Test period for Temp., irradiation, condensation, spray can be adjustable Lamp 1.8KW Wave length range 290-800nm heating power (or so) 4.0KW humidification (or so) 2.0KW Light irradiance 1200w/m2 Distance between arc center and sample holder: 350~380mm Revolving speed of sample holder ≥1r/min  water spray period a. spray time: 0~99h59min (Continuing or adjustable) b. stop time: 0~99h59min, (Continuing or adjustable)   lighting time Continuing programming control available black panel temp. 85±3℃ cooling method Mechanical wind cooling; Room temp. less than 26℃ is recommend, relative humid: ≤85%R.H; humid. and temp. tested after 2 hours under idle condition. 4.Temperature & humidity running control system controller imported programmable 7inch touch screen precision range set precision: temp. ±0.1℃, humid: ±2%R.H, indicated precision: temp.±0.1℃,humid.: ±1%R.H temp. & humid. sensor Platinum Resistance(PT100Ω/MV) black panel temp. double-metal black panel temp. thermometer water-supplying system auto-control humidication water-supplying, Xenon arc lamp with cycling cooling water circulation system low noise heat-resistance conditioning motor, multi-blade centrifugal wind wheel control system mainly consists of operation panel, central controller, kinds of key-pressing sw., status indicating lamp, excution electric device etc.. 5.Structure section of machine body The chamber consists of several section: chamber body, control system, refrigeration system, heating system, humidation system, wind system, raining system, lighting system and so on. Chamber body a. With integrated structure, the chamber consists of up left part as working room, up right part as electric controller which is convenient to control, down part as compressor cooling group, sample holder rotation device, Xenon lamp condensation water box, water pump and other executive devices. b. Inner wall of chamber adopts international SUS304# material. c. Temp. insulation material is polyurethane foam and ultra-fine fibre glass, with good temp. insulation result, no frost and condensation on the external surface of chamber. d. condensate water outfall set at the bottom of chamber e. Environmental heat-resistance silicon sealing tape as the material of door frame. f. Viewing window with eye-protective film on its surface to protect eyes from being injured by Xenon lamp. external chamber body a. Seal of door adopts the double-layer of refined silicone rubber with reliable sealing effect and no aging or hardening phenomenon under high or low temperature. b. Single door (embedded handle); c. Viewing window, antifrost device and lamp equipped on the door viewing window Size:25 cm W × 30 cm H;equipped with Anti-radiation hollow glass 6.Electric control section of chamber a. As the core part of chamber b. Air pressure switch as the main switch to control the main circuit; c. Safety measures for electric section: it warns and cut electricity automatically after tested the action from following protection devices: a) overheat protection in working room b) lockage of phase, leakage protection c) overcurrent protection of motor d) overpressure/overload protection of cooling machine e) short out/overload protection of heater, humidifer f) fusing protection of fuse 7.Working section of chamber Condensation section of compressor. a.Cooling system: as the core part of cooling system, we adopt one set of compressor of Tecumseh from France in this case to ensure the cooling requirement in the working room. b.For adjustment technology and design of cooling system, we take an efficiency processing way to ensure the adjustment for the cooling amount and consumption of cooling system under the normal running, to make the failure rate down to the economical statue. c.Cooling evaporator: it locates in interlayer at one side of chamber which ventilate by force from blast motor to exchange heat fast. d.Cooling method of cooling system: forced air cooling Cooling refrigerant:Environmental R404a; Heating system a. Heating method: heating directly in the chamber; b. Military level stainless steel heating tube used, with fast and stable heating to keep temperature in the working room from rapid change. It with corrosion resistance, anti-high-low temperature, no leakage and other advantages. c. With SSR (solid relay)output control, without noise, reliable working, long service life time, fast switching, low interference from outside, and easy operation etc.. Rain system.   it consists of nozzle, solenoid valve, water-supplying and connecting pipe. Lighting system. It consists of xenon lamp, lamp cover, lamp contactor and other controlling parts. Energy compensation is got by adjusting samples distance, pressure and current. Wind system  It locates in the interlayer at the back of chamber, there are heater, fan blade, evaporator, PT100 temperature samples sensor etc.. when wind machine running, the air is intaken to the channel from working room, and blow out from the bottom after cooled; the air exchanged in the working room with samples is intaken again to the channel and mix; after several circulation, it will reach the purposed temperature, and ensure the high index of temp. and humid in the chamber at the same time. Cooling dehumidification system take the compressor of world brand Tecumseh from France to keep constant temperature, decrease the humidity in the working room and cool the xenon lamp. Humidification Steam generator: to generate steam from water Water level control: control the water inlet by solenoid valve, and water level by liquid level switch to provide the signal for water-supply and warning. Air circulation section Cycling channel and winding machine inside the chamber, it uses the high efficiency cooling machine and energy adjusting system, efficiency heat exchange to reach the aim of temperature change, which also improves the airflow and heat exchange between airflow, heating and humidification, as a result, it improves the humidity uniformity in the working room. 8. Enclosured files: operation manual, warranty card 9. Machine running requirements Temp. 5℃~+32℃ Humidity ≤85% Power supply AC220(±10%)V/50HZ    10. Core components parts Remark: replacement of some small parts of the same quality is possible because of material shortage.    
Temperature & Humidity Test Chamber Temperature & Humidity Test Chamber OTH-150DJ
OTH-150DJ is used to test the performance of materials in various environments and test the heat resistance, cold resistance, dry resistance and humidity resistance of various materials. It is suitable for quality testing of products such as electronics, electrical appliances, mobile phones, communications, instruments, vehicles, plastic products, metals, food, chemicals, building materials, medical care, and aerospace.  
UV lamp aging test chamber UV lamp aging test chamber GB-OUVA-115
Accelerated weathering tests are performed on materials by simulating ultraviolet radiation and condensation in natural sunlight to obtain results on material weathering resistance. It can simulate environmental conditions such as ultraviolet, rain, high temperature, high humidity, condensation, and darkness in natural climates. By reproducing these conditions, it can be combined into a cycle and allowed to automatically complete the cycle as required.
Gas Permeation Tester Gas Permeability Analyzer for Testing Packaging Material GTR - N530
GBPI Gas Permeability Tester N530 demonstrate how to test gas volumn pass through your packaging material
aluminum film Vacuum Coating Thickness Tester Vacuum Coating Thickness Tester For Vacuum Aluminum Film GH-E
Vacuum Coating Thickness Tester is applied to various vacuum aluminum film, aluminized paper, and other conductive coating materials to test the resistance value, evenness, thickness and so on.
Falling Dart Impact Tester Falling Dart Impact Tester GBD-L2
GBD-L2 falling dart impact tester is suitable for testing materials such as plastic film or sheet and steel plate coating with a thickness of less than 1mm. Under a given height of free falling dart impact, it can measure the energy (in Quality to express results) of plastic films,thin section specimens and other materials. Through the impact resistance test, it can prevent the packaging surface from being damaged when the packaging material is impacted or dropped due to insufficient toughness of the packaging material, and effectively avoid the product from being damaged due to impact or falling in the circulation link. It can be used in scientific research, teaching, industrial and mining enterprises, laboratories, research institutes and quality supervision departments.
migration tester Full-Automatic Overall Migration Tester AUTO ZF3600
  AUTO ZF3600 Total Migration & Non-Volatile Residue Tester Full-automatic Evaporation Residue & Loss on Drying Analyzer for Pharmaceutical, Food Contact, Chemical & Water Quality Testing Need technical datasheet, quotation or application support? Get free consultation from GBPI's testing instrument experts. Click for Free Consultation Introduction The AUTO ZF3600 Total Migration & Non-Volatile Residue Tester adopts an integrated system design of water bath evaporation, heating drying, cooling and constant-weight weighing. The whole test process runs fully automatically without manual operation. It is suitable for total migration (non-volatile residue, evaporation residue) tests in purified water, pharmaceutical packaging materials, food contact materials, cigarette tipping paper, chemical reagents and other fields. It can also be used for moisture content and loss on drying of solid samples, as well as total dissolved solids testing in water quality inspection. Test Principle Transfer the test solution into the solvent dish of the automatic feeding system. The empty dish is heated, cooled and weighed according to the set temperature. Repeat the steps until the constant weight is reached. The solution is evaporated to dryness in a water bath below the boiling point of the immersion liquid. The chamber is heated to 105℃ for drying and then cooled. After the evaporating dish is cooled, the balance judges the constant weight, and the experiment ends once the constant weight requirement of the test item is satisfied. Schematic Diagram of Principle Compliance Standards Purified Water: Purified Water in Chinese Pharmacopoeia Volume II, EP9.0 WATER, PURIFIED Pharmaceutical Packaging: Non-volatile residue item in extractables test of National Pharmaceutical Packaging Material Standard Food Contact Materials: GB 31604.8-2021, EN 1186-3:2002 method A, Standards and Specifications for Utensils, Containers and Packages of Korea Ministry of Health and Welfare chapter IV 2-8 Cigarette Tipping Paper: YQ/T 59-2015 Chemical Reagents: GB/T 9740-2008, ISO 759 Water Quality: GB 8538-2016, DZT0064.9-2021, GB/T 14415-2007, GB/T 5750.4-2006 Solid Samples: Extractables and Loss on Drying in Chinese Pharmacopoeia Volume IV, USP40-NF35<921> WATER DETERMINATION Specifications Item Technical Parameters Measuring Range 0 g ~ 80 g Balance Resolution 0.1 mg Balance Weighing Range 0 g ~ 220 g Constant Weight Tolerance 0.3 mg, adjustable Water Bath Temperature Range Ambient ~ 100℃ Oven Temperature Range Ambient ~ 125℃ Temperature Control Accuracy ±0.5℃ Number of Sample Positions 36 Evaporating Dish Volume 100 mL Gas Port Size Φ8 mm Overall Dimension 1200 mm(L) × 850 mm(W) × 1335 mm(H) Power Supply 220V,50Hz Rated Power 7000 W Operation System Windows 10 Pro 64-bit Features Dual-temperature Integrated Control System, Upgraded Automation Integrated workflow of water bath evaporation, drying, cooling and constant weight for automatic, efficient and precise testing. Adopts automatic feeding mechanism controlled by pneumatic valve with residual volume less than 0.1 mL, no waiting or manual attendance required. Built-in water bath with liquid level sensor for automatic water level detection, water filling, draining and temperature control. High-precision Imported Balances with Isolation Protection Equipped with 3 high-precision imported balances, constant weight of 0.3 mg can be achieved after two drying cycles. Balances are installed in a stable shield with water-circulation interlayer to keep stable temperature and humidity during weighing. High Throughput & Wide Compatibility 36 independent test stations with separate data output to meet high-throughput testing needs. Compatible with purified water, n-hexane, ethanol, acetic acid, chloroform and other organic solvents. Cooling & Recovery System for Efficient Solvent Recycling Built-in circulating water cooling pump maintains low chamber temperature. Eco-friendly, cooling down to room temperature within 30 min. Equipped with solvent recovery bottle, solvent recovery rate over 90%. Intelligent Operating System, Global Compliance Real-time display of weighing data, temperature and humidity curves; data is automatically saved for query. Designed in accordance with GMP annex for computerized systems, flexible parameter setting for different standards. Audit trail function for full data traceability, user permission management available. Supports multiple data output formats, electronic signature and online report approval. Laboratory Intelligent IoT Platform The instrument can connect to the IoT platform for network digital management. Authorized users can remotely log into the IoT platform, access the instrument software interface, manage test data and perform remote fault diagnosis. Application Image Application Field Description Purified Water Suitable for testing the non-volatile content of purified water and sterile water for injection in the pharmaceutical industry. Pharmaceutical Packaging Materials Suitable for the test of non-volatile matter items in the dissolution test of plastic and rubber pharmaceutical packaging materials. Food Packaging Materials Suitable for various food utensils, containers and food packaging films, cans or other various food tools, pipes and other products made of polyethylene, polystyrene, polypropylene, perchlorinated vinyl resin as raw materials in different food simulants. Determination of total migration after immersion. Cigarette Pack Materials Suitable for total migration test of cigarette tipping paper soaking solution. Chemical Reagent Suitable for the evaporation residue test of chemical reagents, such as ethanol, acetic acid, n-hexane, chloroform and other organic solvents whose boiling point is lower than 100℃. Domestic Water and Drinking Water, Industrial Water, Sewage Suitable for the total dissolved solids test of drinking water, drinking natural mineral water, groundwater, drinking water, swimming pool water, urban sewage, industrial boiler water, etc. Solid Samples, Pharmaceutical Particles Suitable for loss on drying, dry content or moisture testing of solid samples, such as hollow capsules, noncrystalline cellulose and other pharmaceuticals or other solid particles. Ready to upgrade your total migration and non-volatile residue testing workflow? Contact GBPI today for datasheet, quotation and professional testing solution. Click for Free Consultation
Film Heat Shrinkage Tester GBK-D1 DIN 53369-1976 Pet Film Heat Shrinkage Tester Thermal Shrinkage Tester For Plastic/PVC /OPS Film
Film Heat Shrinkage Tester tests various heat shrinkage propertiesforthe filmaccording to the principle of air heating (air bath).Suitable for heat shrinkable films which produced with polyethylene, ethylene copolymers and their mixtures, such as beverage labels, bottled bundle packaging, sausage shrinkage packaging, outer film of daily chemical products, outer film of cigarette boxes, etc. It is a device that can accurately and quantitatively measure the thermal shrinkage force, cold shrinkage force, shrinkage rate, shrinkage time and other properties of plastic films during thermal shrinkage.
Electronic Tensile Tester Electronic Digital Tensile Tester Machine GBL-H2
  GBL-H2 Universal Single Column Electronic Tensile Tester Product Introduction Developed by R&D team of Guangzhou Biaoji Packaging Equipment Co., Ltd., GBL-H2 universal single column electronic tensile tester complies with GB, ASTM and other relevant standards and market demands. Equipped with high-precision sensors, it features high force measurement accuracy, stable loading and long service life. The LCD screen with professional software displays real-time test curves and data, and supports test report query for easy operation. With fully automatic control unit, it is equipped with complete safety protection functions including limit protection, overload protection and emergency stop. This tester is used for tensile, peeling, heat seal, tearing, puncture and other mechanical property tests of metallic and non-metallic materials. It meets the technical requirements of national supervision departments, and is widely applied in quality control of plastic film, food and pharmaceutical enterprises, as well as scientific research and teaching experiments of testing institutions and schools. Test Principle Fix the prepared specimen between two clamps. Start the instrument to make the two clamps move relatively. The force sensor on the moving clamp collects force changes during the test, and the built-in displacement sensor records displacement changes. Finally, the mechanical indicators such as tensile strength, peeling strength, heat seal performance and tearing strength of the specimen are calculated. Compliance Standards GB 8808, GB 13022, GB/T 1040, GB 4850, GB/T 7753, GB/T 7754, GB/T 453, GB/T 17200, GB/T 16578.1, QB/T 1130, GB/T 2791, GB/T 2790, GB/T 2792, GB/T 7122, GB/T 10004, GB/T 17590, JJG 139, GB/T 6344, GB 10808, YBB 00112003, YBB 00102003, YBB 00132002, YBB 00202004, ASTM D828, ASTM E4, ASTM D882, ASTM D1938, ASTM D3330, ASTM F904, JIS P8113, QB/T 2358 Technical Parameters Force Measuring Range 0~300 N (Optional: 0~500 N) Force Measuring Accuracy Within ±0.5 %FS (Class 0.5) Test Speed 0~500 mm/min (Stepless speed regulation) Displacement Accuracy Within ±0.5% Effective Test Width 30 mm (Customizable: 50 mm, 60 mm) Effective Test Stroke 750 mm (Customizable: 1000 mm, 1200 mm) Overall Dimension L×W×H:600 mm×500 mm×1300 mm Weight 65 kg Power Supply AC 220 V,50 Hz Product Features Elegant and portable desktop single-column structure, comfortable for sitting operation. Supports tensile, peeling, heat seal, tearing, puncture and other tests; multiple adjustable parameters. High sampling rate (100 times/second) ensures accurate test data. Three-level safety protection with emergency stop switch. Adopts imported core components for high precision and long service life. LCD screen displays real-time data and working status. Intelligent operating system supports user management, authority management and audit trail, complying with GMP computerized system requirements. It can work independently or connect with computer for online testing, and the built-in printer outputs data in real time. Optional laboratory intelligent IoT platform, realizing data management and remote fault diagnosis.
  • Facebook
  • Linkedin
  • Youtube
  • Twitter

Copyright @ 2026 Guangzhou Biaoji Packaging Equipment Co.,Ltd. All Rights Reserved.

Chat now

Inquiry Now

Home

Products

NEWS

contact