packaging testing equipment Water Vapor Permeation Tester
Products
Home /

Environmental Test Equipment

/Ozone Aging Test Chamber (Dynamic Stretching) GB-OCY-150M

Ozone Aging Test Chamber (Dynamic Stretching) GB-OCY-150M

Inquiry now
Product Detail

1 Function

Ozone in the atmosphere is very little, while it’s a major factor in rubber cracking, the product simulate and enhance atmospheric ozone condition to study the role of ozone on the rubber, and to rapid identificate and evaluate rubber resistance for ozone aging and anti-ozone agent protection. According to“GB / T7762-2003 Test Method for Static Tensile Test of Ozone Resistance Cured Rubber or Thermoplastic Rubber”,“GB / T2951.21-2008 General Test Method for Insulation and Sheathing Material of Cable”,“GB / T 11206-2009 Rubber Aging test surface cracking method”, and other relevant standards of the test method.

2.1 Structure 

All-in-one machine

2.2 Material

a) Inner chamber: SUS304 stainless steel plate

b) External chamber: SUS304 stainless steel plate or baking finish.

Insulation: rigid polyurethane foam + aluminum insulation cotton with double protection.

2.3 Machine door

a) Single door, open from left.

b) Window frame / door frame with two silicone rubber seal and anti-condensation heating device.

c)With observation window (W220xH250mm), lights above the window and door. 

2.4 Requirements for sample holder (for dynamic-type only)



 

a)At both ends of the sample to be fixed with a clamp under the required elongation, the longitudinal direction of the specimen shall be substantially parallel to the direction of air flow when in contact with ozonized air.

b) Clamps shall be made of a material (eg aluminum) which does not readily decompose ozone.

c) Allow the sample to rotate at a speed between (20 ^ -25) mm / s, in a plane perpendicular to the dry gas flow, with each sample moving continuously along the same path.

d) The time of one revolution of the same specimen is (8 ^ -12) min. The scanning area of the specimen shall be at least 40% of the effective area of the test chamber.

Specimen preparation shall conform to the provisions of GB / T 9865.1. The test specimen is preferably cut from the new test piece and, if desired, may be cut from the finished product. At least 3 specimens shall be required for per test condition. The standard length of the specimen is not less than 10mm, and thickness not less than 0.2mm. The length of specimen between the two ends of the clamp before drawing is not less than 40mm.

3 Control panel

a) Controller display

b) Power switch

c) Fault alarm

d)Wavelength switch

e)light switch button

4 Enclosure configuration

a) With a stainless steel SUS # 304 shelf turntable

b) One φ50mm lead hole:, and with a hole cover and silicone rubber plug.

c) Move casters 4 pcs

d) Horizontal mounting brackets 4 pcs

e) There is a drainage hole in the back of the machine to facilitate the drainage of condensate; (8mm in diameter)

Three-phase five-wire cable (four-core cable + protective grounding wire) 1 pc, (three meters long).

Send A Message

Leave us a message, we will get back to you ASAP.

Related Products
Professional PCT Test Chamber / Pressure Cooker test chamber GB-OPCT-30 supplier PCT Test Chamber / Pressure Cooker test chamber GB-OPCT-30
1.Function It’s widely used in rubber products, magnetic materials, circuit boards, muti-layer circuit boards, IC, LCD, electronics and other products sealing performance testing. 2.Characteristics 1) The imported double-temperature structure with high temperature resistant solenoid valve is used to minimize the failure rate. 2) Independent steam generation chamber to avoid direct impact of steam on the product, so as not to cause partial damage to the product. 3) The door lock labor-saving structure solves the shortcomings of the locking difficulty of the first-generation product disc handle. 4) Cool air before the test; the design of the exhaust air in the test (air discharge in the test barrel) improves the pressure stability and reproduction. 5) Ultra long-term experimental running time up to 400 hours. 6) Water level protection, through the test room water level Sensor to detect protection. 7) Tank with anti-pressure design, the box body with pressure (150 ° C) up to 2.65kg, in line with the water pressure test of 6kg. 8) Two-stage pressure safety protection device, adopting two-stage combined controller and mechanical pressure protection device. 9) Safety protection pressure button, two-stage automatic pressure button for emergency safety device. 10) Bias test terminal withstand voltage up to 3000V (optional) 11) USB for exporting the history data, curve. 3.Technical parameters 1)Temperature range: +100°C~+132°C (Saturated vapor temperature) 2)Humidity Range: 100% steam Humidity 3)Humidity Control Stability: ±1%RH 4)Working pressure: 1.2~2.89kg/cm2 (including 1atm) 5)Time Range: 0 Hr to 999 Hr 6)Pressurization time: 0.00 Kg ~ 1.04 Kg/cm2 about 45 minutes 4.Material of chamber 1)Test chamber size:∮300 mm x L500 mm; 2)Overall size: W900x D900 x H1400 mm; 3)Inner barrel material: Stainless steel plate material (SUS# 316, 3mm); 4)Outer barrel material: stainless steel plate material or spray plastic; 5)Insulation material: rock wool and hard polyurethane foam insulation 6)Steam chamber heating tube: Titanium tube is heated and never rusts. 7)Control System: Taiwan-made Delta color touch PLC to control humidity and steam temperature (using PT-100 Platinum temperature sensor). (Imported large-screen touch controller) 5.Mechanical structure 1)Round inner box, stainless steel round test inner box structure, in line with industrial safety container standards, can prevent dew condensation design during test. 2)Round lining, stainless steel circular lining design, can avoid direct impact of vapor latent heat on the sample. 3)Precision design, good air tightness, low water consumption, and can be operated continuously for 400Hrs every time. 4)The patented packing design makes the door and the box more tightly combined, which is completely different from the traditional extrusion type, and can extend the packing life. 5)Critical point LIMIT mode automatic safety protection, abnormal cause and fault indicator display. 6)Security Protection: a)Imported high temperature sealed solenoid valve adopts double circuit structure to ensure no leakage of pressure. b)The whole machine is equipped with over-pressure protection, over-temperature protection, one-button pressure relief, manual pressure relief and multiple safety guarantee devices to ensure users to the greatest extent. c)Use and safety. d)Back pressure door lock device, the test box door cannot be opened when there is pressure inside the test chamber. 6.Other accessories. 1)Test rack 1 group 2)Sample tray   7.Ambient environment & Facilities. 1)It can be allowed to use the working environment temperature 5 ° C ~ 30 ° C; experimental water: pure water or distilled water 2)System power fluctuations should not be greater than ± 10, 220V 20A.
Professional Salt spray test chamber GB-OSH-60 supplier Salt spray test chamber GB-OSH-60
1. FunFunction Salt spray test chamber is used for the quality inspection and corrosion resistance test of a variety of materials, including metal plating, metal, electronic components, chemical coatings, paint, automobiles, motorcycles, metal ware, screws, springs, magnetic materials, organic and inorganic coating, anodizing, anti-rust oil industry etc. after the surface treatment. 1. ecGTechnical parameters 1. MODEL GB-OSH-60 2. Temperature inside chamber 35℃±1℃/ 50℃±1℃ 3. Temperature of pressure barrel 47℃±1℃/ 63℃±1℃  4. Inner size W600 x H400 x D450mm   5. External size W1080 x H1080 x D650mm 6. Temperature Uniformity ≤±2℃ 7. Uniformity Fluctuation ≤±0.5℃ 8. Salt fog settlement 1~2ml/h.80cm2 9. Compressed air pressure 1.00±0.01kgf/cm² 10. Spray mode Continuous or intermittent spray optional 11. Power supply AC  220V   50Hz   1.5KW a)  Temp. range: RT+10℃ ~ 55℃ (temperature up to 50C, thickening PVC or PP material is recommended ) b) Humid. range: ≥93%R.H c) Controller time shown: 9.9s~9990hrs d) Timer: 0~9999hrs. e) Testing method: Neutral salt spray test (NSS test), acetic acid salt spray test (AASS test), salt spray test (SS test), copper accelerated acetic acid salt spray test method for salt spray test (CASS test) and so on; (For CASS test, we recommend the PP material chamber with high temperature resistance) f) Specimen holder: It can meet the tilt test at 15 ℃ ~ 30 ℃ (two layers); g) Air compressor: V-0.013/12.5(Customer provided); discharge pressure:1.25M; flow amount: 0.13m3/min   1. MMMaterial of machine body a) Salt spray chamber adopts the quality PVC reinforced hard plastic plate, the surface is smooth and anti-aging, anti-corrosion; b) Without any FRP material produced on the surface because of discoloration fibrosis. Plastic structure of the chamber is better to meet strong acid salt spray test under long-term without any damage. c) Cover is imported transparent impact-resistant plate which is convenient to test specimen when test, that can cover and the box with a water seal to prevent leakage of salt spray.   2. AccAccording to CSN, JIS, ASTM standards, can be set to constant temperature control: (a) Brine spray test: NSS (neutral); · Temp. inside chamber: 35 ℃ ± 1 ℃ · Pressure air bucket: 47 ℃ ± 1 ℃ (b) Corrosion resistance test: CASS (copper acceleration), AASS (acid) · Temp. inside chamber: 50 ° C ± 1 ° C · Pressure air bucket: 63 ℃ ± 1 ℃   3. Watwatering system. It adopts the auto watering system, supply water when lack of water. 4. HeaHeating system Test temperature inside the cabinets is heated humidification water jacket, the heater adopts advanced titanium protective tube, built-in nickel-chromium alloy infrared heater core. Heating up fast, uniform temperature distribution; and saves about one half of the power compared to FRP tank jacketed heating. 5. ExeExecutive standard GB/T 2423.17 Basic test procedures for electric and electronic products Ka"- salt spray test methods; GB/T 10125 Corrosion tests in artificial atmospheres – salt spray tests; ASTM B368 Test Method for Copper-Accelerated Acetic Acid-Salt Spray (Fog) Testing (CASS Test); JIS Z2371-2000 Methods of salt spray testing etc. ISO 9227 Corrosion tests in artificial atmospheres (Note: 2 collection device is required, bigger models than ZH-SH-90 (270L) is required; In some versions, it specifies over 400liters is necessary)  ASTM B117-18 Standard Practice for Operating Salt Spray (Fog) Apparatus (Note: 2 collection device is required, bigger models than ZH-SH-90 is required )
Professional UV lamp aging test chamber GB-OUVA-115 supplier UV lamp aging test chamber GB-OUVA-115
Profile The UV Accelerated weathering test chamber stimulates dew and rain with consideration for humidity and/or water spray equipped with a fluorescent UV lamp which can completely simulate the UV spectra of sunlight, exposes materials to alternating cycles of UV light and moisture at controlled, elevated temperatures. It’s most widely used weathering tester to test types of damages include color change, gloss loss, chalking, cracking, crazing, hazing, blistering, strength loss and oxidation. The source adopts 8 pieces of UV lamps of 40W as the light source. The lamps are distributed on the two sides of machine, 4 pieces for each side (UVA-340 and UVB-313 optional), 8 pieces in total . 1.Main technical parameters Item UV Lamp aging test chamber Model GB-OUVA-115   Interior size   W1150 X H400 x D500mm Exterior size W1350 X H1450 x D650mm Weight 120kgs Controller -LCD 7-inch touch screen controller, with programmable temp., humid., UV(sun), and time and Fix mode of 2 running modes.    -USB interface -Operation button -Alarm indicator -Irradiation timer Temp. control mode PID self-adjustment SSR control Temp. range RT+10℃ ~ 70℃ (adjustable) Temp. deviation ±2.0℃ Temp. fluctuation ±0.5℃ Humidity range ≥93%R.H Temp. uniformity ±1℃ Temp. fluctuation ±0.5℃ Distance between lamps 75mm±15mm Distance between samples and lamps 100 ~ 50mm±30mm Irradiation level ≤1.1W/m2 adjustable Adjustment Test period for Temp., irradiation, condensation, spray can be adjustable Irradiation lamp ATLAS Lamp UVA-340, L=1200/40W, 8pcs (average service life: 1600hrs)   Temp. control method PID self-adjustable SSR control Depth of water channel 25mm under auto-control UV Wavelength UVA-340: 315 ~ 400nm; Test time 0~999 H 99 min (adjustable) Function Temperature, light, condensation, spray test cycle is adjustable Black board Temp. 50℃ ~ 70℃ (temperature inside the chamber plus 20℃ ~ 25℃) 2.Structure & Material a)Structure: The middle of the machine is the working chamber, the water system located at the bottom of machine, its top is the control cabinet and control panel. Open the door from front direction. The bottom of the chamber with high-quality PU activity wheel that can be fixed, users can move it according to their requirements positioning. -Single cycling system for air flue in the box, there’s one inlet axis weeding machine which improves the flow amount of air, the heating ability and the whole temperature uniformity in the test machine. -Water source and consumption: Tap water or distilled water for 8liters per day. -Heating method is to heat liner water tank with fast heating speed and high temperature uniformity. b)Material: -Inner box: high grade stainless steel plate -Outer box: stainless steel plate SUS304 or stoving varnish for option. 3.Spray System -Using the manual control function of the controller, to observe the spray condition in the open-door state, so as to adjust or replace the nozzle. -The machine is equipped with a sprinkler, the sprinkler simulates the temperature upheaval and rain erosion during the rain, with a total of several nozzles, sprayed evenly. The spray time is set by the customer. -Inner water level is with automatic water replenishing. 4.Light source system Types of light source (simulate the sunlight) Light source: 4 imported UV fluorescent lamps (ATLAS) with rated power of 40W, UVA-340 and UVB-313 light source for users to choose. Like other lamps, the aging of the QUV tube causes the lamp output to drop, and the QUV without the Irradiance meter control system uses the rotational position method to compensate. This system can be used for many application standards, but it has inherent limitations. This method of changing position does not compensate for the effects of different batches of lamps or the surrounding environment. 5.UV Cycle Temperature control The components of the UV cycle system include a blower, air heater, air distribution system, and blackboard temperature sensor. a)Blower: Installed in the lower tank air duct of the equipment, the blower is continuously operated throughout the UV cycle. b)Air heater: Installed in the air duct above the blower to heat the air blown by the blower when needed. c)Air distribution system: The air blown by the blower enters the test chamber through the air duct, and then the air guide to the entire chamber. 6.Heating system a)High speed heating tube of U-shape titanium alloy; b)independent temperature control system and lighting system; c)temp. control and output power controlled by micro computer with high accuracy and high efficiency. d)Thermal protection function of heating system. -The black panel adopts the colorful touch screen controller or digital key pressing controller to control the heating process. PID self-regulation, monitoring all adopt the standard PT100 temp. sensor of black panel. Temp. of water tank adopts the colorful touch screen touch screen program to control the heating, water tank locates at the bottom of tank, there is electrical heating device. During the test process, there’s test phase is dark condensation which need to generate saturated steam of high temperature, when steam meet the cool temperature, it condenses into water on its surface. 7.USB port (standard) All the history curve and history data can be downloaded from controller as Excel or JPG according to date. 8.Standards compliant GB/T14552-2008 "National Standard of the People's Republic of China - Plastics, Coatings, Rubber Materials for Machinery Industry - Artificial Climate Accelerated Test Method", a, fluorescent UV / condensation test method. GB/T16422.3-1997 GB/T16585-96 Relevant analytical methods. GB/T16585-1996 "National Standard of the People's Republic of China - Test Method for Artificial Weathering of  Fluorinated Rubber (Fluorescent UV Lamp)". GB/T16422.3-1997 "Plastics Laboratory Light Source Exposure Test Method" and other corresponding standard terms and design standards. In line with international testing standards: current ultraviolet aging test standards such as ASTM D4329, ISO 4892-3, ISO 11507, SAE J2020. 9.Safety protection device a)Ground protection b)power source overload and short circuit breaker c)control loop overload and short circuit fuse protector d)water shortage protection e)thermal protection 10.Quality assurance system Sailham strictly follows the requirements of ISO9001:2015 quality management system and European CE product certification. 11.Standard accessories attached to machine Stainless steel SUS # 304 Shelf layer 1pc Power cord 1pc A drain hole (8 mm in diameter) Operation and maintenance instructions 1 copy Controller manual 1 copy Warranty card 1 copy 12.Equipment ambient environment -Grounding resistance cable is less than 4Ω; -Requires users to configure the device at the installation site for the capacity of the air or power switch, and the switch must be independent for the device (plug-socket is not allowed); -Temperature: 5℃ ~ +30℃ -Humidity: ≤85% -Pressure: 86kPa ~ 106kPa -Power supply: AC220 (±10%) V, 50 / 60HZ   -Power: 4.5KW 13.Core components parts. Remark: replacement of other parts in the same brand as material shortage. Parts Brand (origin) Touch screen controller Independent R&D software, Delta controller UV lamp USA /ATLAS/QLAB Stainless steel inner and externer sheel OHKURA (Japan) AC contactor Schneider (France) Heating tube Taiyi (Taiwan) Humidification tube Taiyi (Taiwan) Intermediate relay Japan IDEC Heating tube Taiyi (Taiwan) S.S.R TOONE (CN) Ballast CN PAK Electrical (CN) Regulator module LONCONT (CN) Spray Water pump CN Linxiao Draught fan TECO (Taiwan) Dimming module Japan Panasonic Overtemperature protector  RAINBOW (Korea) Flat handle OHKURA (Japan)  
synthetic blood penetration tester Mask Synthetic Blood Penetration Tester
It is suitable for the resistance of the mask to the penetration of synthetic blood under different levels of test pressure. The mask material is tested with synthetic blood under continuously applied pressure, and the penetration of synthetic blood on the material is visually checked.
Box Compression Tester Box Compression Tester for corrugated box and packing box
Box Compression Tester mainly used in various types of corrugated box and packing box. It is the basic instrument for corrugated carton such as small and medium-sized packing box of the compression strength performance test. The various performance parameters and technical indicators is in line with ISO2872 The Package – Complete and Full Transport Package- Compression Test ", ISO2874 The Package – Complete and Full Transport Package-Stacking Test using pressure testing machine "
WVTR Testing Equipment Moisture vapor transmission rate (MVTR)-AUTO W806
product description This product is based on the principle of water vapor transmission test by cup method and designed and manufactured with reference to ASTM E96, standard, providing a wide range and high efficiency water vapor transmission rate test for low, medium and high water vapor barrier materials. It is suitable for water vapor transmission performance testing of films, sheets, papers, fabrics, nonwovens and related materials in the fields of food, pharmaceuticals, medical devices, daily chemicals, etc.
Thickness Tester Plastic Film Digital Thickness Tester
Didital thickness tester is used to make thickness measuring or comparative measuring of plastic film, thin sheet, paper and so on.
Elmendorf tearing strength tester GBD-S ASTMD689 Elmendorf Tearing Strength Tester For Fabric And Paper
The tear tester (elemendorf method) tests the tear resistance of paper, film, PVC, polyolefin, polyester, composite film, sheet, non-woven fabric, textile, paper, and board, etc. It is controlled by computer automatically and can be tested independently.
Compression Resistance Tester Compression Tester for Bag Packaging GBN200A
Compression tester is used to test the compression resistance of packaging bag.
Mask Tester Respirator Fit Test Machine Mask Tester & Supplies
GB-MH180 Respirator Fit Test Machine is a specialized instrument for measuring leakage ratio of dust concentration quantitatively in and out of mask to select fitted mask and check leakage, which is compatible with the requirements of OSHA and GB 19083-2010 .The Respirator Fit Test Machine is widely used in workplaces such as hospitals, manufacturing plants, production sites, and other testing institutions.
Atmosphere Refrigerator AUTO GQ900 Modified Atmosphere Refrigerator
AUTO GQ-900 Modified Atmosphere Refrigerator is mainly for a variety of fruits, vegetables, flowers, seedlings, etc. on the market for storage and preservation tests, through microelectronics technology to automatically control the concentration of oxygen, nitrogen, carbon dioxide, ethylene in the box, as well as control temperature, humidity conditions to achieve the preservation effect, is a microorganism, environmental protection, food production, universities, scientific research institutions and other units indispensable ideal equipment.
 Folding Endurance Tester Folding Endurance Tester on paper for cardboard and other flaky materials
Folding Endurance Tester mainly test the folding endurance on paper, cardboard and other flaky materials, but the thickness less than 1.25mm. Its main technical indexes and performance parameters accord with related national standards.
  • Facebook
  • Linkedin
  • Youtube
  • Twitter

Copyright @ 2023 Guangzhou Biaoji Packaging Equipment Co.,Ltd. All Rights Reserved.

Chat now

Inquiry Now

Home

Products

News

contact