Heat Seal Tester is to test the temperature, pressure, and time for heat sealing of various film materials.

 plastic film, food and drug manufacturer, the scientific research and teaching experiment of testing institutions and schools    

Heat Seal Analyzer widely used in industries of plastic films, food, pharmaceuticals, inspection agency, research institute and so on,it is to test the temperature, pressure, and time for heat sealing of various film materials.    

  GBB-C Vertical Heat Sealing Tester Product Introduction GBB-C vertical heat sealing tester accurately measures heat sealing temperature, time, pressure and other performance parameters of plastic stand-up pouches, paper-plastic composite pouches and metal composite pouches. Optimal sealing conditions can be confirmed by testing sealing characteristics of different packaging materials. Testing Principle Place sample on the lower support plate and adjust height properly. Set sealing temperature, time and pressure as required, then start the device. The upper fixture seals samples automatically according to preset parameters. Step on foot switch to complete sealing in manual mode. In automatic mode, cyclic sealing runs repeatedly following set duration. Compliance Standards QB/T 2358-1998, ASTM F 2029, YBB00122003-2015 Technical Parameters Temperature Range Room temperature ~ 250℃ Temperature Accuracy ±1℃ Sealing Time 0.1s ~ 99.99h Sealing Pressure 0~1 MPa Sealing Surface 300×5.5mm smooth cutter, lower rod with silicone pad Operation Mode Manual & Automatic, external cylinder Air Source Compressed air Overall Dimension 730×400×540 mm Weight 33.8kg Power 1200 W Power Supply AC 220V, 50Hz Product Features Independent Temperature Control Temperature sensors installed at the rear of sealing cutters, inner and outer cutters support separate temperature setting. Dual Optional Test Modes Automatic mode realizes efficient repetitive sealing; manual mode equipped with foot switch for safe and easy operation. Advanced Pneumatic Driving System Composed of pressure gauge, regulating valve and cylinder, air pressure can be precisely adjusted for stable and efficient sealing work. Comprehensive Customization Service Anti-stick coating upgrade available. Customizable shape, size and surface smoothness meet diversified research demands. Application Fields Plastic Stand-up Pouch Paper-plastic Stand-up Pouch Aluminized Stand-up Pouch Boxed Milk

GBB-F1 Heat Seal Tester is to test the temperature, pressure, and time for heat sealing of various film materials. It is applied to quality inspection organizations, drug control institutions, research institutes, packaging, thin film, food companies, pharmaceutical enterprises, personal care industry and so on.

Product Introduction The LC-3S manual precision sample cutter can be used for precision sample cutting in tensile testing of materials such as copper-aluminum foil, battery separators in the new energy industry, various plastic films, paper, paper-plastic composites, and metals. This product is easy to operate, safe, reliable, and durable. The cut samples are smooth without burrs, enabling precise cutting of samples and effectively avoiding measurement errors caused by poor sample cutting.   Product Features Item Technical Parameters Material Thickness ≤1mm Cutting Specification 15mm × 220mm (customizable) Equipment Size 250mm × 550mm × 400mm Weight 9kg   Product Features ✦ The sample cutter has a compact design, is sturdy and durable, easy to operate, and efficient.✦ The cutting blade is made of high-speed tool steel, with a high-hardness edge that is sharp and durable. The cut samples are undamaged with smooth edges without burrs.✦ The width of the cut sample is 15mm, with high cutting precision, fully meeting standard requirements. It also supports customization of different sample cutting widths.✦ Both sides of the blade are designed with safety protection barriers, ensuring safe and reliable sample cutting process.

MC‑D Migration Test Cell: Professional Pre‑Treatment Solution for Food‑Contact Material Migration Test GBPI MC‑D Migration Test Cell for Food‑Contact Material Migration Pre‑Treatment Address: No.3 Linjiang Road, Xiagang Subdistrict, Huangpu District, GuangzhouTel: +86 15820231129 | Official Website: www.gbpitester.com Product Introduction MC‑D Migration Test Cell is suitable for pre‑treatment of migration tests for food‑contact materials and products. It meets the requirements of GB 5009.156‑2016 and applies to all non‑volatile food simulants specified in GB/T 23296.1‑2009, GB 31604.1‑2015 and other relevant standards. It provides standardized test conditions to support safety assessment for food‑contact specimens, widely adopted by third‑party laboratories, food packaging manufacturers and research institutes. Executive Standards To ensure test repeatability and global recognition, MC‑D Migration Test Cell conforms to both Chinese national standards and European normative requirements: GB/T 23296.1‑2009, EN13130‑1:2004, GB 5009.156‑2016, GB 31604.1‑2015, EN1186‑1:2002. It satisfies migration pre‑treatment requirements for domestic inspection and EU export certification. Core Technical Parameters Contact Mode Single‑sided contact Contact Area 99.17 cm² Contact Surface Diameter Φ112.4 mm Volume 300 mL Operating Temperature 5℃ ~ 120℃ Product Features • Designed and manufactured with reference to Type‑D cell in Appendix C of EN1186‑1:2002, Type‑D cell in Appendix D of GB/T 23296.1‑2009 and Type‑D cell in Appendix D of EN13130‑1:2004, ensuring consistency of migration test results. • This migration cell supports both migration‑cell method and total‑immersion method to meet diverse pre‑treatment requirements. • Constructed of premium borosilicate glass featuring high hardness, high light transmittance and excellent chemical stability. It is heat‑resistant with low matrix content and will not interfere with the determination of overall migration and specific migration values. • Adjustable stainless‑steel latches enable simple operation and reliable sealing. It prevents burst under high‑temperature conditions with various food simulants, guaranteeing test safety and stable migration results. • For non‑reflux immersion, the opening can be sealed and fixed directly with glass plug to carry out total‑immersion tests at ambient and high temperatures. • For reflux immersion, a condensation reflux tube can be directly connected to the ground‑glass joint for migration testing. Application Fields It applies to migration test pre‑treatment of food‑contact materials and products exposed to food simulants including water, acetic acid and ethanol. Conclusion MC‑D Migration Test Cell is a standard‑compliant auxiliary device for food‑contact material safety testing. Made of high‑performance borosilicate glass, it supports both migration‑cell and total‑immersion approaches, compatible with non‑reflux and reflux immersion workflows. With safe anti‑burst performance under high‑temperature testing, it delivers repeatable migration pre‑treatment results for lab QC, third‑party testing institutes and packaging manufacturers. It is essential hardware for food‑contact material compliance assessment both for domestic market and European export business. Get Quotation for This Unit GBPI Packaging Test Equipment ManufacturerAddress: No.3 Linjiang Road, Xiagang Subdistrict, Huangpu District, Guangzhou, Guangdong, ChinaTel: +86 15820231129 | Official Website: www.gbpitester.com

Vacuum Coating Thickness Tester is applied to various vacuum aluminum film, aluminized paper, and other conductive coating materials to test the resistance value, evenness, thickness and so on.

The spout sealing machine is specialized in automatic casing and heat sealing machines for straws and bags, and can be applied to a variety of different types of straws, straws of different calibers and lengths. Applicable to different bag types, stand-up bag, three-side sealing bag, slanted bag, penguin bag. Products are suitable for a variety of industries, beverages, daily chemicals, medicine, food, etc. It has the characteristics of light weight, small footprint, simple operation and stable performance. The main components are all made of aluminum and stainless steel, which meet the environmental and hygienic quality requirements of food and drug GMP.

One test chamber water vapor permeability analyzer using weight reduction method is to test the water vapor transmission rate (WVTR) of films or sheets materials.

Product Introduction This professional machine is designed for automatic tube insertion and heat-sealing of straws and bags. It is suitable for straws of various diameters, lengths, and models, making it the preferred automated equipment for packaging bags such as laundry detergent spout side bags, beverage/juice spout bags, oil/grease spout bags, and inclined-mouth outdoor foldable water bags. It can be customized to connect with filling production lines.

  1. FunFunction Salt spray test chamber is used for the quality inspection and corrosion resistance test of a variety of materials, including metal plating, metal, electronic components, chemical coatings, paint, automobiles, motorcycles, metal ware, screws, springs, magnetic materials, organic and inorganic coating, anodizing, anti-rust oil industry etc. after the surface treatment.   1. ecGTechnical parameters   1. MODEL GB-OSH-60 2. Temperature inside chamber 35℃±1℃/ 50℃±1℃ 3. Temperature of pressure barrel 47℃±1℃/ 63℃±1℃  4. Inner size W600 x H400 x D450mm   5. External size W1080 x H1080 x D650mm 6. Temperature Uniformity ≤±2℃ 7. Uniformity Fluctuation ≤±0.5℃ 8. Salt fog settlement 1～2ml/h.80cm2 9. Compressed air pressure 1.00±0.01kgf/cm² 10. Spray mode Continuous or intermittent spray optional 11. Power supply AC  220V   50Hz   1.5KW a)  Temp. range: RT+10℃ ~ 55℃ （temperature up to 50C, thickening PVC or PP material is recommended ） b) Humid. range: ≥93%R.H c) Controller time shown: 9.9s~9990hrs d) Timer: 0~9999hrs. e) Testing method: Neutral salt spray test (NSS test), acetic acid salt spray test (AASS test), salt spray test (SS test), copper accelerated acetic acid salt spray test method for salt spray test (CASS test) and so on; (For CASS test, we recommend the PP material chamber with high temperature resistance) f) Specimen holder: It can meet the tilt test at 15 ℃ ~ 30 ℃ (two layers)； g) Air compressor: V-0.013/12.5(Customer provided); discharge pressure:1.25M; flow amount: 0.13m3/min   1. MMMaterial of machine body a) Salt spray chamber adopts the quality PVC reinforced hard plastic plate, the surface is smooth and anti-aging, anti-corrosion; b) Without any FRP material produced on the surface because of discoloration fibrosis. Plastic structure of the chamber is better to meet strong acid salt spray test under long-term without any damage. c) Cover is imported transparent impact-resistant plate which is convenient to test specimen when test, that can cover and the box with a water seal to prevent leakage of salt spray.   2. AccAccording to CSN, JIS, ASTM standards, can be set to constant temperature control: (a) Brine spray test: NSS (neutral); · Temp. inside chamber: 35 ℃ ± 1 ℃ · Pressure air bucket: 47 ℃ ± 1 ℃ (b) Corrosion resistance test: CASS (copper acceleration), AASS (acid) · Temp. inside chamber: 50 ° C ± 1 ° C · Pressure air bucket: 63 ℃ ± 1 ℃   3. Watwatering system. It adopts the auto watering system, supply water when lack of water. 4. HeaHeating system Test temperature inside the cabinets is heated humidification water jacket, the heater adopts advanced titanium protective tube, built-in nickel-chromium alloy infrared heater core. Heating up fast, uniform temperature distribution; and saves about one half of the power compared to FRP tank jacketed heating. 5. ExeExecutive standard GB/T 2423.17 Basic test procedures for electric and electronic products Ka"- salt spray test methods; GB/T 10125 Corrosion tests in artificial atmospheres – salt spray tests; ASTM B368 Test Method for Copper-Accelerated Acetic Acid-Salt Spray (Fog) Testing (CASS Test); JIS Z2371-2000 Methods of salt spray testing etc. ISO 9227 Corrosion tests in artificial atmospheres (Note: 2 collection device is required, bigger models than ZH-SH-90 (270L) is required; In some versions, it specifies over 400liters is necessary)  ASTM B117-18 Standard Practice for Operating Salt Spray (Fog) Apparatus (Note: 2 collection device is required, bigger models than ZH-SH-90 is required )